Project Chocolate Temptation
- Thread starter KoSoVaR
- Start date
I have now made an extender/raiser to the PSU, I thought to mount PSU as I showed above, the raiser will raise the PSU from the case's bottom and then I can mount the power cord on the bottom where I can access the switch on a light way
, I will use myself out of 25mm M3 screws, it will be so fine!
Has also changed the banner ... finally
!
, I will use myself out of 25mm M3 screws, it will be so fine!
Has also changed the banner ... finally
When was the last for a very long awaited update from Kosovo!
I finally got my Paracord yesterday and I have started a little bit with Sleeving, PSU is almost done anyway, it looks like it's just two of the 4-pin ATX connectors and the 24pin ATX left, it is damn was at night and the network is pretty tough when there are 6-7 computers on 0.5mbit -.-, for those of you who do not know how to sleeve with Paracord, let me just say that it comes up a Paracord-Sleeving guide on Sweclockers soon!
the first thing I did was I started with my sata to molex cable loop ...
Now I have cut away the extra touch that I do not need
They will be soldered like this!
Time to solder !
Then, the loop is finished, time to start Sleeving, but first ... cut the original sleeve!
I will begin with 6pin cables ... this is what I had in mind ... but I changed my mind later!
My package from knivbutik.se....
The Paracord 550...colordifferences
This Paracord contains seven pieces of threads that are interwoven in sets consisting of the 3 other threads ...
test sleeve a little and it went well
... however, so I did not know if I would run with or without heat shrink :/
I prepared more paracord pieces, as you can see I have taped as well marked on the tape where I'm going to cut ... this to Paracord not fry it very much to do, remove the wires and burn the edges of paracorde with the tape on, when you done this you can remove the tape without any problems
I was for braids for a while ... but it will do it on another project
, I want this to have a nice flow through the whole thing
I sleeved the 2x 6pin cables and my SATA molex cable!
the 6pins will sit like this into the graphic card...it will look totaly awsome !
'
It was this update, sorry for those poor pictures, only had access to a digital camera in low light and the images were not very good ...
I finally got my Paracord yesterday and I have started a little bit with Sleeving, PSU is almost done anyway, it looks like it's just two of the 4-pin ATX connectors and the 24pin ATX left
, it is damn was at night and the network is pretty tough when there are 6-7 computers on 0.5mbit -.-, for those of you who do not know how to sleeve with Paracord, let me just say that it comes up a Paracord-Sleeving guide on Sweclockers soon!the first thing I did was I started with my sata to molex cable loop ...
Now I have cut away the extra touch that I do not need
They will be soldered like this!
Time to solder !
Then, the loop is finished, time to start Sleeving, but first ... cut the original sleeve!
I will begin with 6pin cables ... this is what I had in mind ... but I changed my mind later!
My package from knivbutik.se....
The Paracord 550...colordifferences
This Paracord contains seven pieces of threads that are interwoven in sets consisting of the 3 other threads ...
test sleeve a little and it went well
I prepared more paracord pieces, as you can see I have taped as well marked on the tape where I'm going to cut ... this to Paracord not fry it very much to do, remove the wires and burn the edges of paracorde with the tape on, when you done this you can remove the tape without any problems
I was for braids for a while ... but it will do it on another project
I sleeved the 2x 6pin cables and my SATA molex cable!
the 6pins will sit like this into the graphic card...it will look totaly awsome !
It was this update, sorry for those poor pictures, only had access to a digital camera in low light and the images were not very good ...
dugdiamond
New member
spam
Hey mate, may want to re-upload those photos elsewhere, your bandwitdh's exceeded.
yeah i know i just wrote that on the second post
dugdiamond
New member
why so many pics to show so little???
EDIT: welcome - but these pics need to be sorted dude
EDIT: welcome - but these pics need to be sorted dude
why so many pics to show so little???
EDIT: welcome - but these pics need to be sorted dude
There are many pictured but my photobucket pro went out yesterday and the bandwith is exeeded, i will but another photobucket pro as i usally do, the problem is taht i have forgot my creditcard back home in sweden, im in vocation in kosovo right now but i have my psu with me so that i can sleeve it
Thanx!-i will as soon as i can !
Sounds interesting, need to re-upload your pictures though
Thanx- i will buy Photobuchet Pro as soon as i can
Looking nice! Well the sleeving so far.
I'm really liking the browns, don't think there are too many brown looking builds out there.Glad you're going to get the photobucket sorted! Need to see the goods.
Hehe sorry for that...it isnt my bad that im so MR Popular haha xD!
Yeah i love brown, and i have always wanted to do a brown themed project and finally i am doing this
daniSAUR
New member
Hehe sorry for that...it isnt my bad that im so MR Popular haha xD!
Yeah i love brown, and i have always wanted to do a brown themed project and finally i am doing this, Yes i will buy one more month of photobucket pro and you can se all the other updates...but the problem is taht i have forgot my creditcard at home back in sweden haha XD, im recently in kosovo now for a vocation, luckely i brought the PSU with me so i can kill that boring spare time with some nervbreaking sleeving
Didn't think you could get bored... on holiday!
Also, did you not use any heatshrink on the sleeved cables?
Didn't think you could get bored... on holiday!But each to their own.Well I can't wait to see the images, well looking forward to this.
Also, did you not use any heatshrink on the sleeved cables?
Who doesnt not get bored by fixing thier brand new appartment
No i crimped the paracord together with the cable itself
daniSAUR
New member
Who doesnt not get bored by fixing thier brand new appartment, great !
No i crimped the paracord together with the cable itself
Neat idea! May consider this next time I sleeve cables.
