ExtremePrometeia Baker Extreme

[Phil Stanbridge]

A little project we are working on.. We are in the testing phase at the mo, and hope to go live with this very shortly, but things are looking exceptional so far!

So far temps are -82 degrees under no load.

Once this little beaut is ready it will be going live on the site, you'll soon be able to own your very own customised EPUK Mach II GT.

Here's the evidence

 

[Phil Stanbridge]

ooooh its chilly...

 

[HARRY]

me likes verry much ,have you replaced the temp senser

 

[Psykotik]

The sensor reading is wrong, as the Mach II control board goes nuts after about -60, but it is damn cold

 

[HARRY]

i wonder how manny whats it can remove

 

[Psykotik]

That will depend on the length of the cap tube used and how the charge is tuned, but at a guess I'd say it will be optimised for 170 W at -60, maybe lower, for an A64 rig and if the cap tube is kept at stock length, then it will dissipate 200 W at a rather low temp.

The mounting is much better than the existing Prommi mount tho, which is a bonus

 

[Phil Stanbridge]

yes we need to fluke it in order to get a totally accurate temperature.

 

[fatty]

Hmmmmm looks bloody awsome think I need a bit of that subzero action

 

[standin wave]

yes we need to fluke it in order to get a totally accurate temperature.

Phil is there any chance you'd have time to do a 'This is how it is all connected picture guide" for the Mach II GT - there's always the danger a wire comes loose etc and you're stuffed cos it isn't always obvious where it went! The pictures should be sufficient explanation in themselves, so you wouldn't need words - see 'smiling pussies' thread - nuff said?

sw

 

[Firelord]

Nice one phil looks nuts

baker18s block mount makes soo much more sense! How much will one of those be going for?

 

[Phil Stanbridge]

Nice one phil looks nuts

baker18s block mount makes soo much more sense! How much will one of those be going for?

Well... We have yet to set a firm price, but I will be selling these as new units on the site at a retail price of approx £650. This will get you everything you need (Mach II GT, Baker Head preinstalled, blue LCD, cpukit mounting) plus warranty, which is all important. The mod can also be done to any Mach II for a smaller sum, but this will be dealt with on a "per job" request.

 

[Phil Stanbridge]

The first unit is live and up for grabs! £650 gets you a tried and tested r507 Baker Extreme. For more info check out the site!

 

[Animal]

Phil can u tell me how much it would cost to say send u a unit and get a baker head put on..?

 

[fatty]

Phil are you going to look at the chilly1 head mods as well

 

[Phil Stanbridge]

Phil can u tell me how much it would cost to say send u a unit and get a baker head put on..?

Yes thats possible, if you provide the baker head and the fittings it would cost you £300 to have it professionally installed.

 

[Phil Stanbridge]

Phil are you going to look at the chilly1 head mods as well

yes mate, chilly1 mods are next on the cards

 

[dillingerdan]

yes mate, chilly1 mods are next on the cards

Are chilly1's block better than Baker18's? I saw some of Chillys and they looked very similar so I'm guessing the main difference is internal. Also they come in different sizes, which would you get Phil?

I have a question about the fitting also mate, when you do a unit, say I sent my GT would you regas to r507 or could we keep it stock? Also can you tune the cap tube for a lower wattage?

 

[SoundWave]

The first unit is live and up for grabs! £650 gets you a tried and tested r507 Baker Extreme. For more info check out the site!

How's the noiselevel on that thing? Doesn't the fans need to run on Turbo at all times, when modded with R507?

Awesome temps by the way.

 

[dillingerdan]

Also will you be able to get the Vapo LS mount kit for use with these? (Obvious that modification is need for the larger block) It's now available aswell as the Skt T kit HEREhttp://www.asetek.com/default.asp?s...=sideid&myvalue=14&contentSection=2&menuID=-1

 

[Phil Stanbridge]

How's the noiselevel on that thing? Doesn't the fans need to run on Turbo at all times, when modded with R507?

Awesome temps by the way.

Thanks for the comments, the unit can be ran at normal levels ala Mach II but it is recommended to run the fans at max power for obvious reasons. When you venture into extreme cooling you have to make comprimises somewhere down the line.