Recent content by hardw1re

Well... after 2 years of faithfull service, my Mach II has found its way to the bin :( [well not that far yet] but after preparing my new case for it, well it decided it'd spring a leak :( At the moment i havent the money to repair/replace such an expensive cooling unit, so i am back to...

Anyone got an online manual for the mach 2? i have no idea where mine is, and i cannot reemmber what the red light means. im having some trouble with stability and starting up my system. I gave that psu calculater a wiz and it reckons i only need 383Watts to run my system... i think thats wrong...

Ok originally i upgraded the control board to a GT control board, without the lcd display at the time, Phil recommended me to use a specific firmware for it, i am suspecting in that firmware the lcd display is disabled(?) that is why when i fitted it several minutes ago i have had no output on...

ok here is my system: http://homepages.shu.ac.uk/~pnwright/computer.jpg i sent phil a message but hopefully some-one else here can help me out, i want to get hold of some 4mm perspex to be able to replace the side and front panels of the mach II unit to make the entire thing match. Any ideas...

Hey Guyz, (currrently using my old Abit KT8 Pro board) used PCB lacquer on the board to help protect the components, and used a good amount of seal string to make a tight seal - but on the back plate, and around the mach head there is a high condensation build up - the mach evaperator sits...

Ok, well as many of you know i've been having some problems with my system since the other week. i have just got home from being away. As usual without a CPU in it the Neo 2 it will turn on as soon as you put power to it. I have just put a brand new 3000+ in - using the HS for now, even though...

Ok, i've come across a problem. The reason why i was getting that condensation on the back of my case was caused by too much dialetic grease, causing the seal string to not make an effective seal. So yesterday i took the lot apart and spent ages trying to get as much of it off as possible, but...

I dont get it, the Evap head is reading -61 degree's Celcius. Yet the system is telling me my CPU is at a constant 40 degree's Celcius with/without load?!

will the mach 2 head fit on an MSI K8N? i was just looking over the photo of the board and its not easy to tell if it will fit or not. does anyone else know? - ignore this thread i just found one about 939 agp bpards.

i cant remember where it was i read this, if i did or not. but with an AMD 64 system, it is possible to seal it up using Dialetic grease and not seal string? earlier this evening i was trying to take apart the parts sitting around the cpu. got the back off fine, got the evap head off fine, but...

Ok i have just bought a hardcano 9 (fully aware that the spec say's it cannot read below 0 degree's C), i also bought it cause of the 4 fan controllers. but my question is this, does anyone know that if i replaced the thermistor with one that can read below 0 will it work, or would the...

Any of you here play CSS ?? i've been playing it since it was released. am part of www.iengland.org (our site is still being repaired after our server's HDD failed :( ) anyway post here if you play!!

I've been having idea's and designs popping into my head the last few days, this is just a suggestion. well sometime ago i tried to build a copper piped water cooling for my cpu, it actually worked for a while, until where i'd bodged a connection between the copper pipes and the plastic tubing...

Ok, i have been running my Mach II st since august last year - its been ok like, but my temp tends to read between 0 and sometimes as high as 20. now i dont know if this is because im running an ST controller board, or if its the way i have fitted the unit around the cpu. just wondering if...

Hi, i'm trying to find out if it is possible to buy the usb controller that is in the GT(?) version for the ST version?