Xigmatek Utgard Case Vid

Nice review buddy, keep up the good work!
smile.gif
 
Good review - thanks - I've been wanting one of these cases for a while, but they are not available in South Africa
sad.gif
and to import something as big as a case is not really cost effective - the shipping costs are more than the cost of the case.
 
I have this case and i can tell you it can certainly cool well. Very easy to install components. Only problem i had was with the pci tool less mounting orange clips when installing my XFX HD6850. And then using screws is a bit of a pain in the arse... but atleast its not too loud and can handle my OC'd HD6850 keeping it at about 50-60 degrees when playing MOH on max OC'd... obviously with all fans turned up on highest... BUT DEFINITELY WORTH IT FOR A BUDGET CASE!I would recommend to anyone looking to build a budget to mid range gaming rig...
 
ChrisGT said:
Thanks guys. I'm going to be doing a vid showing how easy it is to mount a 240 rad in this case soon.
Click to expand...

fits in the top with the included rad brackets i know i had the case with a sr 240
biggrin.gif
fans can be mounted on top of rad but top cover wont close

so mount fans underneath but becarefull Version 1 of the case had 20mm fan spacing Version 2 has 15mm fan spacing

280mm rads fit aswell
 
Squirrel-666 said:
fits in the top with the included rad brackets i know i had the case with a sr 240
biggrin.gif
fans can be mounted on top of rad but top cover wont close

so mount fans underneath but becarefull Version 1 of the case had 20mm fan spacing Version 2 has 15mm fan spacing

280mm rads fit aswell
Click to expand...

I just wish that space uptop was deeper. You can't run nice thick rad up there. My rx240 holds the top off by half an inch lol. Its good for air or a thin rad watercooling setup.

One of the down flaws of the case is how the top plastic piece is loose. You can move it side to side a few mm. Its just the way they made the case and how they made the clip in system for the whole top assembly where the plastic meets metal.
 
ChrisGT said:
I just wish that space uptop was deeper. You can't run nice thick rad up there. My rx240 holds the top off by half an inch lol. Its good for air or a thin rad watercooling setup.

One of the down flaws of the case is how the top plastic piece is loose. You can move it side to side a few mm. Its just the way they made the case and how they made the clip in system for the whole top assembly where the plastic meets metal.
Click to expand...

The top part on mine doesnt budge at all, maybe was just something wrong with yours? It could be that the pressure from the pipes pushing the rad brackets on mine are forcing it in place though.
 
Mark26 said:
The top part on mine doesnt budge at all, maybe was just something wrong with yours? It could be that the pressure from the pipes pushing the rad brackets on mine are forcing it in place though.
Click to expand...

I thought it was just mine but after taking the top section off you can see its only little tabs holding it in place towards the back. I checked my friends is the same. Its not like easy just blow on it move but if you push on the back end up top it will move right and left.
 
ChrisGT said:
I thought it was just mine but after taking the top section off you can see its only little tabs holding it in place towards the back. I checked my friends is the same. Its not like easy just blow on it move but if you push on the back end up top it will move right and left.
Click to expand...

Just did as you said and doesn't move a mm. Must be because of the rad and pipes then.
 
You must log in or register to reply here.

Similar threads

J
Is LTT forum is choke full of spooks ?
Replies
5
Views
487
hmmblah
hmmblah
AlienALX
The Fairchild Ghost subwoofer project
2
Replies
35
Views
645
AlienALX
AlienALX
WYP
Any Resin 3D printers here?
Replies
5
Views
3K
WYP
WYP
tinytomlogan
New OC3D Website.
2
Replies
31
Views
7K
dipzy
dipzy
AlienALX
My very rarely seen Fallout collection.
Replies
0
Views
1K
AlienALX
AlienALX
Back
Top