dieseldog49
New member
Just ordered a fan controller and some wiring, plus I am headed back to Bryans shop tomorrow to have the PSU bracket made up.
Last edited:
Bombproof Builders Desk.....Build
- Thread starter dieseldog49
- Start date
dieseldog49
New member
Ok a slightly smaller update today. I am still waiting on some parts to arrive (A huge thanks to deadlift1 you are truly [H]ard!) He offered me some free extensions so I can use compression fittings on my reservoir. However I did swing back by Bryans shop to have a PSU Bracket mad up yesterday and I got the rest of the mounting hardware for the tray installed.
First off is the Latch to hold it in the upright position, nothing fancy but it works like a charm.
Then we have a tensioning cable to reduce stress on the wood the hinges are mounted to and prevent sag. I mounted a adjustable hook on one end so I can adjust sould the cable stetch out or I need to alter the position.
Then off to the plasma cutter again.
And viola a PSU bracket.
Mounted.
And we now have a place to slap in the Seasonic 750w PSU
You can see here the PSU has plenty of room to breathe and there is only a slight gap between the wood which I will address when I do cable management.
Hopefully another update and maybe a video by the weekend. As always thanks for reading!
First off is the Latch to hold it in the upright position, nothing fancy but it works like a charm.
Then we have a tensioning cable to reduce stress on the wood the hinges are mounted to and prevent sag. I mounted a adjustable hook on one end so I can adjust sould the cable stetch out or I need to alter the position.
Then off to the plasma cutter again.
And viola a PSU bracket.
Mounted.
And we now have a place to slap in the Seasonic 750w PSU
You can see here the PSU has plenty of room to breathe and there is only a slight gap between the wood which I will address when I do cable management.
Hopefully another update and maybe a video by the weekend. As always thanks for reading!
andrevautour
New member
Looking forward to a video--I just subscribed to your channel 
Last edited:
nikhiljudge
New member
looks good would love to see the finished product!
dieseldog49
New member
Thanks Andre! I will be resuming making videos soon, my old camera broke and I hadn't been willing to pony up the $400 for another until a few weeks ago.
nikhil, you shouldnt have to wait too much longer, as soon as I get the wall build finished I will be tearing apart my main system to get it in the desk.
nikhil, you shouldnt have to wait too much longer, as soon as I get the wall build finished I will be tearing apart my main system to get it in the desk.
nikhiljudge
New member
looking forward to it!!!
dieseldog49
New member
I just spent the last 4 hours in a modding haze, all I know is I have re worked all of the tubing with Tygon, I am out of heat shrink and I have watched far too much Top Gear. Update tomorrow 
SPS
Moderator
I just spent the last 4 hours in a modding haze, all I know is I have re worked all of the tubing with Tygon, I am out of heat shrink and I have watched far too much Top Gear. Update tomorrow
Haha excellent
dieseldog49
New member
Ok guys, I am getting close to being done, last night though I decided I needed to re work a bunch of stuff to get the Wall PC right, so I ended up working until 3am on it then spent the next 3 hours after that ordering more parts. So much for this being a ultra cheap build ( Facepalm) Anywho on with the update.
First off is wiring up the power and restart buttons, I am using a run of cat5 wire so that if I decide to get LED buttons later on I can use the extra 2 pairs for the LED's, Green is Power, Orange is Reset.
Side note I found a great new way to use the little LED flashlight in my mini leatherman
Now that gets passed through the wall and that brings us to the wall side wiring.
First off the Fans, I am using a Phobya fan splitter.
Now Cables you see here from left to right, Pump Cables,Power Switch Cat5 Cable then the Fan Power cable.
Here is what its shaping up like on top, please ignore the terrible wire sleeving as I realized the stuff I have it just terrible and I have just ordered Paracord this morning. I also will be sleeving all of the Seasonic PSU cables as well, which will be a first for me.
Now I also decided to replace of of the tubing with Tygon tubing as the Flexability will come in handy plus I get to use Mayhems Deep red Dye for a better color scheme
Next up is test fitting my hard drive mounting solution, a Syba Dual Slot 2.5 caddy.
Its quite light and should suite my needs quite nicely, I have a 1tb Spinner and a Intel 160gb SSD in the mail. I also have the wall pass through and a USB slim housing for a disk drive as well as a couple other things on their way. As always thanks for reading!
First off is wiring up the power and restart buttons, I am using a run of cat5 wire so that if I decide to get LED buttons later on I can use the extra 2 pairs for the LED's, Green is Power, Orange is Reset.
Side note I found a great new way to use the little LED flashlight in my mini leatherman
Now that gets passed through the wall and that brings us to the wall side wiring.
First off the Fans, I am using a Phobya fan splitter.
Now Cables you see here from left to right, Pump Cables,Power Switch Cat5 Cable then the Fan Power cable.
Here is what its shaping up like on top, please ignore the terrible wire sleeving as I realized the stuff I have it just terrible and I have just ordered Paracord this morning. I also will be sleeving all of the Seasonic PSU cables as well, which will be a first for me.
Now I also decided to replace of of the tubing with Tygon tubing as the Flexability will come in handy plus I get to use Mayhems Deep red Dye for a better color scheme
Next up is test fitting my hard drive mounting solution, a Syba Dual Slot 2.5 caddy.
Its quite light and should suite my needs quite nicely, I have a 1tb Spinner and a Intel 160gb SSD in the mail. I also have the wall pass through and a USB slim housing for a disk drive as well as a couple other things on their way. As always thanks for reading!
dieseldog49
New member
Ok guys, another big update.
I had a bunch of stuff show up today including my paracord
I will be using the 3 colors on the left.
My 160gb Intel SSD and Samsung 1 Tb Spinner for storage.
I also got more heat shrink, ordered a Crimp setup from MDPC. I also got deadlift1's Extensions for the DD res in.
Thanks again man they did the trick perfectly!
So with those, I had everything I needed to get this setup wet. I was super stoked so I started wiring up and sleeving the power and reset switches.
Then disaster, as I was measuring out a wire length and I bumped the latch holding the tray up and slamming it down. The heavy water blocked video card ripped the PCIE 16x Slot right from the motherboard
Now while this is frustrating, it is also entirely my fault, I had considered a better more secure latch but opted for the simpler setup. I am sad to see this mobo die before it even had a chance, I rather liked how basic the bios was and I also liked the built in buttons and display, however I picked this board cause it was on sale and I got it for a good price. I am undeterred however because I really do want to see the effects of cooling a CPU upside down and you can't try something that hasn't been done before without some risk . First priority obviously is a MUCH better latch and then a new motherboard, any suggestions that will go with black, red and grey and are fairly affordable please let me know.
Well instead of posting a video of getting my system topped off with water and leak checked I leave you with pictures of a ruined motherboard but thats modding, some times it all goes terribly wrong and thats what makes it exciting
. Now if you will excuse me I am gonna go to the gym and take my pent up rage at myself and take it out on some weights then have several pints spiked with whiskey.
I had a bunch of stuff show up today including my paracord
I will be using the 3 colors on the left.
My 160gb Intel SSD and Samsung 1 Tb Spinner for storage.
I also got more heat shrink, ordered a Crimp setup from MDPC. I also got deadlift1's Extensions for the DD res in.
Thanks again man they did the trick perfectly!
So with those, I had everything I needed to get this setup wet. I was super stoked so I started wiring up and sleeving the power and reset switches.
Then disaster, as I was measuring out a wire length and I bumped the latch holding the tray up and slamming it down. The heavy water blocked video card ripped the PCIE 16x Slot right from the motherboard
Now while this is frustrating, it is also entirely my fault, I had considered a better more secure latch but opted for the simpler setup. I am sad to see this mobo die before it even had a chance, I rather liked how basic the bios was and I also liked the built in buttons and display, however I picked this board cause it was on sale and I got it for a good price. I am undeterred however because I really do want to see the effects of cooling a CPU upside down and you can't try something that hasn't been done before without some risk
. First priority obviously is a MUCH better latch and then a new motherboard, any suggestions that will go with black, red and grey and are fairly affordable please let me know. Well instead of posting a video of getting my system topped off with water and leak checked I leave you with pictures of a ruined motherboard but thats modding, some times it all goes terribly wrong and thats what makes it exciting
. Now if you will excuse me I am gonna go to the gym and take my pent up rage at myself and take it out on some weights then have several pints spiked with whiskey.williamredpath
New member
This is brilliant work. really looking forward to seeing more. It's build logs like this that really inspire. well done.
dieseldog49
New member
It might be, I am sending it to a member on another forum who said he could fix it, we shall see.
nikhiljudge
New member
ahhh such a shame!!! hopefully ^^^^ can get it fixed for you!
dieseldog49
New member
Sorry I haven't updated lately guys, I received a few pm's last month about the thread on an update and wanted to let you guys know whats going on. I have been busy with real life (Raising a new puppy for search and rescue and lots of search and rescue training and missions have eaten up all my spare time and money.) The project is not abandoned and as winter approaches I will have more time to resume work on it. I am currently looking for a Sandy bridge i5 processor and a 6950 or GTX 580 or better vid card for this project so if anyone wants to donate or sponsor feel free to PM me. Other wise I have to wait till I have more money and time. Thanks though for the interest and comments guys it really keeps me going through the long periods between updates!
