Bent GPU
- Thread starter chiewleong
- Start date
FTR.4500MHz
New member
@ cerbrus2
Did you mod the RV 03 to fit the Rad , and what rad did you throw in there ?
Im going to change my case in the very near future , i am hesitating between RV 03 and a MM Monticle 24 ....
Did you mod the RV 03 to fit the Rad , and what rad did you throw in there ?
Im going to change my case in the very near future , i am hesitating between RV 03 and a MM Monticle 24 ....
@ cerbrus2
Did you mod the RV 03 to fit the Rad , and what rad did you throw in there ?
Im going to change my case in the very near future , i am hesitating between RV 03 and a MM Monticle 24 ....
I mounted a Phobia Gchanger 240X60mm in the 5 1/4 drive bays, you can buy a bracket for £4. And also tom mentioned in a vid about a manufacturer that are making 180 X2 and 180X3 rads that will sit ontop of the huge silverstone fans at the bottom of the case.
FTR.4500MHz
New member
I looked at the review here on the forum and its clearly aircooling designed , are you sur for the 180 rads on the bottom fans ?
The bottom fans dont all sit in one line ....
For the 180 rads i think its Magicool or so .
The bottom fans dont all sit in one line ....
For the 180 rads i think its Magicool or so .
You do have to do a bit of modding to the case, to get it in, a few hole drilled here and their. OR they make a adaptor plate that screws to the top of the fans and then you just mount a 240mm rad to that, and the silverstone fans stay where they are. just depends on how much work you want to do realy. But my nice chunky gchanger went into the drive bays without a hitch and I have also had a 120X40mm rad mounted in the top exuast as well.
FTR.4500MHz
New member
Thank you for the infos matey !
How is the cable management in this case ?
I dont need that much radiator surface anyway since in my actual 600 T i only got a 240 and a 120 ( 30mm thick , 30FPI ) and it does a perfect job on my 2600k @ 4.5 GHz and my 6950's .
Cheers
And as always , have a nice day !
How is the cable management in this case ?
I dont need that much radiator surface anyway since in my actual 600 T i only got a 240 and a 120 ( 30mm thick , 30FPI ) and it does a perfect job on my 2600k @ 4.5 GHz and my 6950's .
Cheers
And as always , have a nice day !
cable management is brill you have around 50mm of space behined the MB tray. only thing it lacks realy is some rubber gromets.
FTR.4500MHz
New member
One more little question ?!
How much space is there between the back of the case and the power supply location ? ( I need 397 mm )
Could you measure that for me please ?
How much space is there between the back of the case and the power supply location ? ( I need 397 mm )
Could you measure that for me please ?
FTR.4500MHz
New member
No mate the 397 mm are for the rad to be fitted !
Back of the case (pci slots) --------------------> Powersupply Housing
You measured from the right side panel .
Back of the case (pci slots) --------------------> Powersupply Housing
You measured from the right side panel .
Rastalovich
New member
Hmmm what interests me about this costing is that if you buy a HP or Dell workstation from the suppliers, and let's say you have a quadro card or similar installed as an extra, the normal box will come and inside the usual plastic bag that has the mouse/build disks etc, will be some of these card retainers.
I'd contact HP/Dell and see if they'll supply you with some. They can't cost much in reality.
oh sorry m8, their is 360mm between the back and the side of the psu casing.
FTR.4500MHz
New member
exactly 360mm ?
The rad wont fit .....
Thank you very much for your time and help !!
So i think im going with the mountain mods case instead .
Cheers , and have a nice day !
The rad wont fit .....
Thank you very much for your time and help !!
So i think im going with the mountain mods case instead .
Cheers , and have a nice day !
jackjack
New member
FTR.4500MHz
New member
Than you for the link Mate !
I just ordered one !
I tried fitting the jack of my car in the case but it didnt work very well !
Cheers !
I just ordered one !
I tried fitting the jack of my car in the case but it didnt work very well !
Cheers !
Mrboxfacetramp
New member
probably the main downside to the RV03 is no water-cooling support
chiewleong
New member
It is one of its kind casing. Like it very much. will put it in the list for next build.I almost brought a Raven RV03 because i didn't like my card bending, the orientation on the motherboard tray means that the card cannot bend
WOW!!! this is superb. too bad that difficult to get a online shop that have shipping to malaysia with acceptable shipping fee.
I wanted to buy a HAF X. just the price shoke me offOr you can buy a HAF-X that comes with a card keeper
