TJ11 Help

[Jacob.xray]

Im planning out my new build and wont to know what the lengths of the front of the tj11 are as im going to see if a 360mm rad (Length of 400mm with end tanks) will fit.

i added a pic with two different colored lines and if someone has the dimensions of both of them it would be much appreciated

http://s1195.photobucket.com/albums...sst_tj11b_w_tower_chassis_review_fulledit.jpg

BTW the red line was ment to go all the way down not stop at the 8th drive bay

 

[006409]

I dont have one but you can basically figure it out by the photo...

each drive bay is 41.3mm high and you have 9 drive bays. so according to that you have 371.7 + a little bit above where the first drive bay begins. Depth wise according to ATX form factor it can be anything up-to 200mm so i think you a 3x120mm in easy saying that drive bays are 146mm wide.

just you'll have to get air in the from some how...

 

[MadMarc]

Why don't you just put a 4x120mm or 4x140mm rad in the bottom? You could even add 280mm or 240mm if you want, no need for a 360 in the front imo, and mesh frontcovers would ruin the looks

 

[Jacob.xray]

Why don't you just put a 4x120mm or 4x140mm rad in the bottom? You could even add 280mm or 240mm if you want, no need for a 360 in the front imo, and mesh front covers would ruin the looks

im going to be ruining 3x 7970 and a 3930k with heavy overclocks and im putting a 4x 120 down the bottom and if i didnt have to mod the case to fit the 400mm long radiator in the front i was going to use 4x 140 instead down the bottom.

so if anyone could find the exact length of the inside of the 9 bays it would be very much appreciated

 

[006409]

i gave them to you... you can fit a 360mm rad in the front even taking into consideration the tanks on the end...

so you can put a 360mm rad that is 80mm thick with push pull easily BUT as has been said i don't think mesh in the front will look nice unless you plan to mod the front that you could do and it could look quite good.

cant you put two 4x140 rads in the base anyway??

 

[MadMarc]

Check out this: http://www.youtube.com/watch?v=3GO_DnAggLI
560mm and 240mm rad in the bottom and the you could add a 120mm at the top, this would give you aboout the same rad capacity as a 480 in the bottom and a 360 in the front but without modding or replacing the drive bay covers

 

[Jacob.xray]

Check out this: http://www.youtube.com/watch?v=3GO_DnAggLI
560mm and 240mm rad in the bottom and the you could add a 120mm at the top, this would give you aboout the same rad capacity as a 480 in the bottom and a 360 in the front but without modding or replacing the drive bay covers

yea i watch him too and i love his videos his tj11 build is why im using the tj11 tbh. and i wonted to go with the 360 in the front because i didn't wont to copy him exactly and i don't mind modding the case.

 

[MadMarc]

yea i watch him too and i love his videos his tj11 build is why im using the tj11 tbh. and i wonted to go with the 360 in the front because i didn't wont to copy him exactly and i don't mind modding the case.

Fair enough, I'm just not sure how it will look like with mesh bay covers as the TJ11's covers aren't flat and I haven't seen matching ones

 

[Jacob.xray]

Has anyone found the measurements yet i would really appreciate it cant find them anywhere