Go Back   OC3D Forums > [OC3D] Project Logs & Gallery > Project Logs
Thread Tools Display Modes
Old 14-08-14, 05:28 PM
Wraith's Avatar
Wraith Wraith is offline
Join Date: Jun 2013
Location: On the Moon.
Posts: 7,620
Wraiths SATA Sleeving Guide

Welcome to my SATA cable Sleeving guide.

First things first, tools you are going to need,

Sleeve. (White 9mm)
Shrink. (Black 12mm)
Sharp Angle cutters.
Sharp Scalpel (stanley knife)
Long nose Pliers.
Lighter or Heat gun.
Cutting mat.
And obviously a SATA Data Cable.

It's worth while saying before I start that if you want a solid colour sleeving job, use a SATA cable that is the same colour as your sleeve, I didn't, because I actually wanted to be able to see the black cable beneath the sleeve.

Step 1.

Take your sleeving and leave it on the roll DO NOT measure it out to length, all will become clear as we proceed, singe the end of the sleeve to gather the loose fraid ends and make the next step so much easier.

Step 2.

Slide your sleeve onto your chosen SATA Cable, it can be a bit of a fiddle but go with it, once your on slide it right to the opposite SATA connector, stop at the connector. Remember you're only covering the cable not the plugs, once you have reached the plug, pinch the sleeve and run your other hand back along the cable to tighten up the sleeve, now that you have done that mark the sleeve where it meets the connector (pictured below).

Step 3.

Now you need to back the sleeve off the cable, once you have enough sleeve backed off (pictured below) you can cut your mark from Step 2. Once you have a nice clean cut, you now have the sleeve at the correct length for your SATA cable, which is why at the beginning I said leave it on the roll now before we slide it back onto the cable you will need to use your lighter again to singe the end to avoid fraying.

Step 4.

Now all you need to do is slide the sleeve back onto the cable and remove the slack by pinching one end and sliding your other hand along the length, you should have something like this pictured below.

Step 5.

Now you take your semi sleeved cable and measure how much shrink your going to need, I've gone for 25mm as I'm covering the plug as well as the sleeve edge. Once cut slide the sleeve over the SATA plug and line it up to where you want it, if your shrink does not slide easily over the plug use your long nosed pliers and stretch out the shrink (don't worry it will close back up).
Next simply apply some heat making sure to rotate the cable as your heating, I used a lighter for this but a heat gun would be my preferred method, take your time with the heat shrink it's not a race.

Step 6.

There is no Step 6! You should if all went well have a nicely sleeved cable, mine is not as perfect as I'd liked but I will redo them later.

Well I hope this was helpful to you, I know I had fun doing it.

“A person who never made a mistake never tried anything new.” ~ Albert Einstein
Reply With Quote
Old 14-08-14, 05:31 PM
RadeonHDx RadeonHDx is offline
OC3D Elite
Join Date: Dec 2012
Location: Yorkshire
Posts: 1,069
WOO! Perfect timing for me Wraith , now I just need to get some bigger heatshrink and some sleeving (I wish paracord could come in a size big enough ).
Intel Xeon E5649 x2 | Custom Water Loop
Saphire R9 290 Tri-X Edition | InWin Dragon Rider White
24GB Samsung RAM | SuperMicro X8DTi R2.0
Samsung Evo 250GB | 1TB Hitachi HDD

Reply With Quote
Old 14-08-14, 05:33 PM
WYP's Avatar
WYP WYP is offline
News Guru
Join Date: Dec 2010
Location: Northern Ireland
Posts: 16,211
Nice job Matey!
Twitter - @WYP_PC
Reply With Quote
Old 16-08-14, 03:50 AM
Lucas Bezerra Lucas Bezerra is offline
Join Date: Feb 2014
Posts: 7
Would we be able to white-tape the cable and fit the sleeve? If yes, I guess this would avoid the black from the sleeve holes. Nice job!
Reply With Quote
Old 16-08-14, 04:58 AM
Excalabur50's Avatar
Excalabur50 Excalabur50 is offline
OC3D Elite
Join Date: Apr 2011
Location: Australia
Posts: 6,239
Top guide Wraith easy to follow with explicit instructions, and they look bloody fantastic too!
NZXT Phantom 630 White=AMD Ryzen 3700X=MSI MPG X570 Gaming Pro Carbon WiFi=Intel Optane SSD 9 480GB PCIE=32gig 3200Mhz GSkill Flare X= Sapphire RX5700XT Nitro Plus=NZXT Kraken X62=MSI Optix MPG341CQR=MSI GK80 Vigor=Corsair Force LS 960GB=Cougar 700M=EVGA Supernova 850 G2=White Sennheiser Game One=NZXT Hue+ with Aer RGB fans and RBG strip=Pioneer BDR-209D=Windows 10 Pro=Thrustmaster T16000M HOTAS=Corsair MM800 RGB CE
Reply With Quote
Old 16-08-14, 11:05 AM
lAnimal's Avatar
lAnimal lAnimal is offline
Join Date: Feb 2014
Location: Offaly, Ireland
Posts: 205
Really informative and clear instructions, anyone else think it should be a sticky?
And nice pics btw
Reply With Quote
Old 16-08-14, 11:06 AM
MadShadow MadShadow is offline
OC3D Elite
Join Date: Nov 2013
Location: St Andrews, Scotland
Posts: 3,282
Originally Posted by lAnimal View Post
Really informative and clear instructions, anyone else think it should be a sticky?
And nice pics btw
Wraith's threads should just be auto-stickied
|i5 4460|8GB RAM|R9 380 4GB|ASUS Z97-I Plus|WD Blue 1TB|Corsair RM650|Phanteks Enthoo EVOLV ITX|

Reply With Quote
Old 16-08-14, 11:28 AM
RamboOC RamboOC is offline
Suspended By Request of Police
Join Date: Jan 2014
Location: UK
Posts: 994
This deserves to be in my bookmarks
Looks like a relatively quick and cheap way to make my rig look better
Reply With Quote
Old 16-08-14, 01:02 PM
Feronix's Avatar
Feronix Feronix is offline
OC3D Elite
Join Date: Aug 2012
Location: The Dungeon
Posts: 7,683
Might have to use this one for my build... Thanks!

"If a bear looks good in the woods when nobody is there, is he still a cool ass motherf***ing bear?" - JR23
Reply With Quote
Old 16-08-14, 03:04 PM
neotrix neotrix is offline
Join Date: Oct 2013
Location: Lincoln UK
Posts: 27
That's the same way I did mine. Avoid tape, especially if it's white! It goes yellow. It's defo worth doing it just the way the post suggests. Good work, and simple to do.
Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT. The time now is 04:44 AM.
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.