Post A Picture of Your Last Purchase
- Thread starter MrKambo
- Start date
SuB
The Webmaster
Are you planning a build Mr. Sub?
More of a transplant
with an added tickle of upgrade.
nevermind 
yassarikhan786
New member
Ethernet cable crimping tool and tester:
SuB
The Webmaster
I plan on doing exactly that this weekend
Anyone know where I can acquire some black coated M3 hex nuts?
I plan on doing exactly that this weekend
HYPE! I'm hyped, I don't know about everyone else but I wanna see! Then i'll want to spend loads of money on my project weeheee!!!!
Hmm.. I don't know SuB, i've been looking around for bolts and screws but i'd not seen many nuts, if you find some good stuff that's cheaper than TTL's epic hardware and of good quality let me know... Or if you wanted to bulk up your order for something epic then I need a few dozen M3 0.5 x 6mm and I guess a shed load of screws for rads, could always get a ton of long ones and cut then down. Drop me a PM if that sounds good.
JR
Last edited:
SuB
The Webmaster
Just ordered 20x4 30mm M3 (black) and 20x4 6mm M3 (black) from E22 fella
very affordable, it's the nuts I could do with really I'll keep looking
Just ordered 20x4 30mm M3 (black) and 20x4 6mm M3 (black) from E22 fella
I'll keep looking
Buy some stainless hex bar, you've got your taps now, sorted!
That E22 is a tidy little store, probably have to 'ave a bit o' that, when i've seen yours
JR
SuB
The Webmaster
Buy some stainless hex bar, you've got your taps now, sorted!
That E22 is a tidy little store, probably have to 'ave a bit o' that, when i've seen yours
JR
Aye, ordered my 10/12 Acrylic tube from there
seems really good! I'm all for supporting the 'little guy' stores if they're stuff is good (like mdpc-x etc)Aye, ordered my 10/12 Acrylic tube from there
Oooh it does look good, the fittings I picked are 10/13 otherwise I might of tried a bit of that. I love MDPC-X too, the little guys who just expand into their little niche of stuff they can ensure are perfect is great.
It's funny E22 don't have any washers either, presumably he must use them on builds perhaps it's worth dropping him an email and asking about nuts/washers?
JR
EDIT:
-DT7bX-B1Mg
Ahhhh FFS...
JR
Last edited:
Dicehunter
Resident Newb
FINALLY SOMEONE SELLS IT.
turns out yoyotech got an exclusive deal with Inwin as the sole uk dealer of this case.
SO HYPE
BUY IT BUY IT BUY IT BUY IT, If I had the chance at this case I would jump at it !!!
barnsley
born in a.....
Nice
The mandrels are lush btw
It is the Primochill branded silicon bendy thing, i'm unsure if it actually has a hole in but I remember reading them saying some of the other silicon bendy jobs can be tight/loose in the tube just due to manufacturer discrepancies on 10mm. Perhaps they have oversized it slightly and added a hole so it can compress a little? I don't know but the monsoon kit has some included too so I will just use whatever works best with the Primochill. Their system is 10/13 so it's quite possible the ID is slightly larger too I guess.
I had to pre-order the mandrels and the 13mm mitre block was the last one special tech had. I couldn't find the entire kit anywhere but to be honest I would sooner buy a slightly higher quality heat gun anyway so it works for me.
JR
SuB
The Webmaster
Yeah I had to order mine in seperate bits, think ocuk had most of it in stock. I have a decent heatgun already thankfully. The monsoon tube is slightly thinner than the one I got from e22 maybe by a mm or so? the fit on the e22 one is almost perfect
Annoyingly the mandrels are for 13mm not 12mm, so there will be some leeway but I can account for this 
