The Official Intel Core 2 Duo Conroe Overclocking Thread

Things have changed a bit since yesterday, so i'll post this entry up :D

DFI LP UT P35-T2R (LP 35DB07 BIOS)

Intel E6600 (L714A245)

2x1024 Crucial Ballistix 8500

X1900 XT-X@689/797, CAT 6.6 DRIVERS

2X36GB Western Digital Raptor 10,000RPM SATA hdd RAID 0

LITEON 832S DVD R/W

Pcp&P Turbocool 1Kw

Mach2 GT/Chilly1/Desuperheater

==========

Code:
[B]Genie BIOS Settings:[/B]

[COLOR=red]

Genie BIOS Setting:

Exit Setup shutdown....................... - Mode 2

CLOCK VCO divider......................... - Auto

CPU Clock Ratio........................... - 8 X

- Target CPU Clock........................ - 4240 MHz

CPU Clock................................. - 530 MHz

Boot Up Clock............................. - Auto

DRAM Speed................................ - 333/667

- Target DRAM Speed....................... - DDR2 1061

PCIE Clock................................ - 105 MHz

PCIE Slot Config.......................... - 1X 1X

CPU Spread Spectrum....................... - Disabled

PCIE Spread Spectrum...................... - Disabled

SATA Spread Spectrum...................... - Disabled

CPU Feature:

Thermal Management Control................ - Disabled

PPM(EIST) Mode............................ - Disabled

Limit CPUID MaxVal........................ - Disabled

C1E Function.............................. - Disabled

Execute Disable Bit....................... - Disabled

Virtualization Technology................. - Disabled

Core Multi-Processing..................... - Enabled

Voltage Setting:

CPU VID Control........................... - 1.6V

CPU VID Special Add....................... - 101.65%

DRAM Voltage Control...................... - 2.23V

SB 1.05V Voltage.......................... - 1.15V

SB Core/CPU PLL Voltage................... - 1.55V

NB Core Voltage........................... - 1.61V

CPU VTT Voltage........................... - 1.58V

Vcore Droop Control....................... - Disabled

Clockgen Voltage Control.................. - 3.45V

GTL+ Buffers Strenght..................... - Strong

Host Slew Rate............................ - Weak

GTL REF Voltage Control................... - Enabled

CPU GTL 1/3  REF Volt..................... - 110

CPU GTL 0/2  REF Volt..................... - 110

North Bridge GTL REF Volt................. - 110

DRAM Timing:

Enhance Data transmitting................. - Fast

Enhance Addressing........................ - Fast

T2 Dispatch............................... - Auto

CAS Latency Time (tCL).................... - 4

RAS# to CAS# Delay (tRCD)................. - 4

RAS# Precharge (tRP)...................... - 4

Precharge delay (tRAS).................... - 12

All Precharge to ACT...................... - AUTO

REF to ACT Delay (tRFC)................... - 24

Preformance LVL (Read delay).............. - AUTO

MCH ODT Latencey.......................... - AUTO

Write to PRE Delay (tWR).................. - AUTO

Rank Write to Read (tWTR)................. - AUTO

ACT to ACT Delay (tRRD)................... - AUTO

Read to Write Delay (tRDWR)............... - AUTO

Ranks Write to Write (tWRWR).............. - AUTO

Ranks Read to Read (tRDRD)................ - AUTO

Ranks Write to Read (tWRRD)............... - AUTO

Read CAS# Precharge (tRTP)................ - AUTO

All PRE to Refresh........................ - AUTO

Clock Setting Fine Delay:

Ch1 Clock Crossing Setting................ - More Aggressive

DIMM 1 Clock fine delay................... - Current[14]

DIMM 2 Clock fine delay................... - Current[ 6]

Ch1 Command fine delay.................... - Current[10]

Ch1 Control fine delay.................... - Current[ 5]

Ch2 Clock Crossing Setting................ - More Aggressive

DIMM 3 Clock fine delay................... - Current[13]

DIMM 4 Clock fine delay................... - Current[ 5]

Ch2 Command fine delay.................... - Current[10]

Ch2 Control fine delay.................... - Current[ 4]

Ch1Ch2 CommonClock Setting................ - More Aggressive

Ch1 RDCAS GNT-Chip Delay.................. - Auto

Ch1 WRCAS GNT-Chip Delay.................. - Auto

Ch1 Command to CS Delay................... - Auto

Ch2 RDCAS GNT-Chip Delay.................. - Auto

Ch2 WRCAS GNT-Chip Delay.................. - Auto

Ch2 Command to CS Delay................... - Auto

Read delay phase adjust:

Channel 1 Phase 0 Pull-In................. - Auto

Channel 1 Phase 1 Pull-In................. - Auto

Channel 1 Phase 2 Pull-In................. - Auto

Channel 1 Phase 3 Pull-In................. - Auto

Channel 1 Phase 4 Pull-In................. - Auto

Channel 2 Phase 0 Pull-In................. - Auto

Channel 2 Phase 1 Pull-In................. - Auto

Channel 2 Phase 2 Pull-In................. - Auto

Channel 2 Phase 3 Pull-In................. - Auto

Channel 2 Phase 4 Pull-In................. - Auto

[/COLOR]

==========

Orthos + 3dMark2001SE:



3dMark2003:



3dMark2005:



3dMark 2006:



==========

short description:

530x8 @ 4240Mhz, Mach2 GT cooling
 
name='cybermaniac' said:
what temps u getting on the latest?

The evap is showing -58c/-60c under dual Orthos. Smartgaurdian though is a waste of time, showing 248c :D. On other mobo's in the past i've always used Speedfan, because it does show negative temps. But on the P35 chipset, as soon as you open Speedfan it provokes a reboot. I might try MBM and see if that works or not.

Past experience with my Mach2 and other mobo's tells me the cpu is probably somewhere around -30c to -25c.
 
Just wanted to update you guys that I'm currently running my E6600 overclocked @3.2GHz (400x8), and this is with Vcore of 1.35V (+100mV Offset) and NB Voltage @1.393V. :D

I could go higher, but then I need to raise the Vcore a bit more, as well as setting the NB Voltage to 1.563V...:rolleyes:

I prefer being on the safe side, so I didn't do it, as I'm very satisfied with my current 3.2GHz overclock. :D

And my CPU runs pretty cool (with my CoolerMaster Hyper 6+) with the CPU idling @31C and never reaches above 45C on maximum LOAD (running Orthos Prime for more than 4 hours!!!) ;)
 
Intel E2140 @3322mhz on Air.

AM3_2140_3322_161848.jpg


3d01_44610_2140_3321.jpg


CPUZ_2140_3321.jpg
 
my E8500/3.16 , i got to 3.6 my crucial ram to 1187, the cpu ran under games at 26c i know i could get more but i am new to oc so just taking my time cheers tork
 
Ok, forgot to post this the other day. Moved on from the E6600, now got an E8500. Just a small improvement over the last post :D

DFI LP UT P35-T2R (03/17/2008 BIOS)

Intel E8500 (Q746A579)

2x1024 OCZ PC9600 FLEX (OCZ2FX12001G)

8800 Ultra @ 710/1140, 169.21 Drivers

2X36GB Raptor RAID 0 / 250GB Caviar

Pioneer DVR 111D

Pcp&P Turbocool 1Kw

Mach2 GT/Chilly1/Desuperheater

==========

Code:
[b]Genie BIOS Settings:[/b]

[color=red]

Genie BIOS Setting:

Exit Setup shutdown....................... - Mode 2

CLOCK VCO divider......................... - Auto

CPU Clock Ratio........................... - 9.5 X

CPU-N2 Ratio.............................. - Disabled

- Target CPU Clock........................ - 4750 MHz

CPU Clock................................. - 500 MHz

Boot Up Clock............................. - Auto

DRAM Speed................................ - 333/800

- Target DRAM Speed....................... - DDR2 1201

PCIE Clock................................ - 100 MHz

PCIE Slot Config.......................... - 1X 1X

CPU Spread Spectrum....................... - Disabled

PCIE Spread Spectrum...................... - Disabled

SATA Spread Spectrum...................... - Disabled

CPU Feature:

Thermal Management Control................ - Enabled

PPM(EIST) Mode............................ - Enabled

Limit CPUID MaxVal........................ - Disabled

C1E Function.............................. - Auto

Execute Disable Bit....................... - Enabled

Virtualization Technology................. - Disabled

Core Multi-Processing..................... - Enabled

Voltage Setting:

CPU VID Control........................... - Auto

CPU VID Special Add....................... - 126.45%

DRAM Voltage Control...................... - 2.27V

SB 1.05V Voltage.......................... - 1.15V

SB Core/CPU PLL Voltage................... - 1.55V

NB Core Voltage........................... - 1.53V

CPU VTT Voltage........................... - 1.17V

Vcore Droop Control....................... - Enabled

Clockgen Voltage Control.................. - 3.45V

GTL+ Buffers Strenght..................... - Strong

Host Slew Rate............................ - Strong

GTL REF Voltage Control................... - Enabled

CPU GTL 1/3  REF Volt..................... - 68

CPU GTL 0/2  REF Volt..................... - 67

North Bridge GTL REF Volt................. - 69

DRAM Timing:

Enhance Data transmitting................. - Fast

Enhance Addressing........................ - Fast

T2 Dispatch............................... - Auto

CAS Latency Time (tCL).................... - 5

RAS# to CAS# Delay (tRCD)................. - 5

RAS# Precharge (tRP)...................... - 5

Precharge delay (tRAS).................... - 15

All Precharge to ACT...................... - 5

REF to ACT Delay (tRFC)................... - 33

Preformance LVL (Read delay).............. - 8

MCH ODT Latencey.......................... - AUTO

Write to PRE Delay (tWR).................. - 13

Rank Write to Read (tWTR)................. - 11

ACT to ACT Delay (tRRD)................... - 3

Read to Write Delay (tRDWR)............... - 8

Ranks Write to Write (tWRWR).............. - AUTO

Ranks Read to Read (tRDRD)................ - AUTO

Ranks Write to Read (tWRRD)............... - AUTO

Read CAS# Precharge (tRTP)................ - 3

All PRE to Refresh........................ - 5

Clock Setting Fine Delay:

Ch1 Clock Crossing Setting................ - More Aggressive

DIMM 1 Clock fine delay................... - Current[44]

DIMM 2 Clock fine delay................... - Current[445]

Ch1 Command fine delay.................... - Current[756]

Ch1 Control fine delay.................... - Current[512]

Ch2 Clock Crossing Setting................ - More Aggressive

DIMM 3 Clock fine delay................... - Current[44]

DIMM 4 Clock fine delay................... - Current[512]

Ch2 Command fine delay.................... - Current[756]

Ch2 Control fine delay.................... - Current[445]

Ch1Ch2 CommonClock Setting................ - More Aggressive

Ch1 RDCAS GNT-Chip Delay.................. - Auto

Ch1 WRCAS GNT-Chip Delay.................. - Auto

Ch1 Command to CS Delay................... - Auto

Ch2 RDCAS GNT-Chip Delay.................. - Auto

Ch2 WRCAS GNT-Chip Delay.................. - Auto

Ch2 Command to CS Delay................... - Auto

Read delay phase adjust:

Channel 1 Phase 0 Pull-In................. - Enabled

Channel 1 Phase 1 Pull-In................. - Enabled

Channel 1 Phase 2 Pull-In................. - Enabled

Channel 1 Phase 3 Pull-In................. - Enabled

Channel 1 Phase 4 Pull-In................. - Enabled

Channel 2 Phase 0 Pull-In................. - Enabled

Channel 2 Phase 1 Pull-In................. - Enabled

Channel 2 Phase 2 Pull-In................. - Enabled

Channel 2 Phase 3 Pull-In................. - Enabled

Channel 2 Phase 4 Pull-In................. - Enabled

[/color]

==========

Orthos:



3dMark2001:



3dMark2003:



3dMark 2005:



3dMark 06:



Aquamark:

normal_Aquamark.JPG


==========

short description:

500x9.5 @ 4750Mhz, Mach2 GT cooling
 
4.75? badass. what cooler are you using again?

(im about to buy that proc, and i want to know what i can get away with.)

The evap is showing -58c/-60c under dual Orthos

wait, what? -58c, as in "negative 58 degrees celsius"? NEGATIVE?
 
name='Orion' said:
4.75? badass. what cooler are you using again?

(im about to buy that proc, and i want to know what i can get away with.)

wait, what? -58c, as in "negative 58 degrees celsius"? NEGATIVE?

Cooling is Phase Change. On air the most you're likely to get stable is between 4ghz and 4.2ghz.
 
Back
Top