Orthos told me...

[mrapoc]

Type: Blend - stress CPU and RAM Min: 8 Max: 4096 InPlace: No Mem: 1791 Time: 15

CPU: 2625MHz FSB: 375MHz [375MHz x 7.0 est.]

CPU: 2625MHz FSB: 375MHz [375MHz x 7.0 est.]

1:Starting MBMStarter.dll...

1:Started MBMStarter.dll: 1

30/05/2007 15:15 1:0/0

1:Temperature: Case: 33.00

1:Temperature: CPU: 44.00

1:====================

Launching 2 threads...

1:Using CPU #0

2:Using CPU #1

1:Beginning a continuous self-test to check your computer.

2:Beginning a continuous self-test to check your computer.

1ress Stop to end this test.

2ress Stop to end this test.

1:Test 1, 4000 Lucas-Lehmer iterations of M19922945 using 1024K FFT length.

2:Test 1, 4000 Lucas-Lehmer iterations of M19922945 using 1024K FFT length.

1:1 minute

1:Temperature: CPU: 55.00

1:====================

1:2 minutes

1:Temperature: CPU: 56.00

1:====================

2:Test 2, 4000 Lucas-Lehmer iterations of M19922943 using 1024K FFT length.

1:Test 2, 4000 Lucas-Lehmer iterations of M19922943 using 1024K FFT length.

1:3 minutes

1:Temperature: Case: 34.00

1:Temperature: CPU: 58.00

1:====================

1:4 minutes

1:Temperature: CPU: 59.00

1:====================

1:Test 3, 4000 Lucas-Lehmer iterations of M19374367 using 1024K FFT length.

2:Test 3, 4000 Lucas-Lehmer iterations of M19374367 using 1024K FFT length.

1:5 minutes

1:Temperature: Case: 35.00

1:Temperature: CPU: 56.00

1:====================

1:Torture Test ran 5 minutes 40 seconds - 0 errors, 0 warnings.

2:Torture Test ran 5 minutes 40 seconds - 0 errors, 0 warnings.

1:Execution halted.

2:Execution halted.

Type: Blend - stress CPU and RAM Min: 8 Max: 4096 InPlace: No Mem: 1791 Time: 15

CPU: 2624MHz FSB: 375MHz [374MHz x 7.0 est.]

CPU: 2625MHz FSB: 375MHz [375MHz x 7.0 est.]

1:Starting MBMStarter.dll...

1:Started MBMStarter.dll: 1

31/05/2007 21:01 1:0/0

1:Temperature: Case: 34.00

1:Temperature: CPU: 46.00

1:====================

Launching 2 threads...

2:Using CPU #1

1:Using CPU #0

2:Beginning a continuous self-test to check your computer.

1:Beginning a continuous self-test to check your computer.

2ress Stop to end this test.

1ress Stop to end this test.

2:Test 1, 4000 Lucas-Lehmer iterations of M19922945 using 1024K FFT length.

1:Test 1, 4000 Lucas-Lehmer iterations of M19922945 using 1024K FFT length.

1:1 minute

1:Temperature: CPU: 56.00

1:====================

1:2 minutes

1:Temperature: CPU: 57.00

1:====================

1:Test 2, 4000 Lucas-Lehmer iterations of M19922943 using 1024K FFT length.

2:Test 2, 4000 Lucas-Lehmer iterations of M19922943 using 1024K FFT length.

1:3 minutes

1:Temperature: CPU: 60.00

1:====================

1:FATAL ERROR: Rounding was 0.5, expected less than 0.4

1:Hardware failure detected, consult stress.txt file.

1:Torture Test ran 3 minutes 48 seconds - 1 errors, 0 warnings.

1:Execution halted.

2:Torture Test ran 3 minutes 48 seconds - 0 errors, 0 warnings.

2:Execution halted.

1:3 minutes 48 seconds

1:Temperature: Case: 35.00

1:====================

Vcore is already at 1.4 and the next one up and ram is loosened to 5-5-5-15 at 2.15v (as high as warranty goes). Shall I try the nb vcore or fsb termination voltage? Those are the only 2 i can see making a difference as I cant go any higher on the other two

 

[mrapoc]

no?

 

[Toxcity]

I would say it is too hot.. :eh:

Or needs more voltage.

 

[llwyd]

Temps are acceptable. I wouldn't usually say that you would need more voltage to get past 2.6 but you may have a poor rev. Usually you get to about 3.3 and need to really crank up the voltage. Put the NB voltage to the middle setting and keep an eye (and finger) on temps, then increase if needs be. Also take as much stuff off auto as possible, ensure memory it set to 2T, etc etc