Is this all I need? =]

[RaiderX303]

27c idle and 51 load is not hot for 3.6GHz 1.575v, only chip i said run hot was my 6300

 

[cuprasport]

bah u aint even got the gtx so its well inferior to the d-tek fuzion

 

[RaiderX303]

bah u aint even got the gtx so its well inferior to the d-tek fuzion

iirc your temps were higher than mine with ur fuzion and E6600 so how can u say the fuzion is better than the apogee

 

[Mr. Smith]

fight fight fight!!!

 

[cuprasport]

i did have 1.6v and 4ghz m8 kinda gets hotter than 3.6@1.575, mines true volts aswell not bios ones,

when i did 1.6v@3.6 my temps were lower than yours u were asking how i got them so low, i will dig some msn history out form my document backups

 

[cuprasport]

fight fight fight!!!

this is a stupid fight tbh we talking about it on msn as we post lol

 

[RaiderX303]

lol, im refering to ur E6600 not E6850, you run that at 3.6 and had higher temps

 

[cuprasport]

the e6600 i ran @3.97, when i had it at 3.6 i was @ 1.45v the only time i over volted 3.6 was when we did our comparison

no way is yours better than mine m8 look at your cheap loop with poor cpmponents

nuff said end of

 

[Mr. Smith]

no way is yours better than mine m8 look at your cheap loop with poor cpmponents

Alright lads I think that is enough.

Play nice

Back on topic...

 

[mrapoc]

hahahahaha we've gone to the "my pc p00ns yuor pc n00b" lol

I can get the d-tek for £27 inc postage (polished before i decide) - reckon i can get him lower

He doesnt have the barbs so ill need a total of 9 x XSPC G1/4" to 1/2" Barb yeh?

Also 9 jubilee clips something tells me xD

 

[RaiderX303]

if you get 7/16" tubing with 1/2" barbs, the plastic clips would be enough as the tube is quite tight over the barbs, looks better than jubilee clips

 

[cuprasport]

id go with 7/16 aswell www.chilledpc.co.uk the high flow barbs there are really good and cheap http://www.chilledpc.co.uk/shop/product_info.php?cPath=34_64_73&products_id=112 direct link

 

[da2ca]

if you get 7/16" tubing with 1/2" barbs, the plastic clips would be enough as the tube is quite tight over the barbs, looks better than jubilee clips

I've read on a few forums that if you use the 7/16 its that tight ion the barb you don’t need any clips. Is this right?

 

[cuprasport]

I've read on a few forums that if you use the 7/16 its that tight ion the barb you don’t need any clips. Is this right?

yes, u need to heat the tubing up sometimes to get it on

 

[da2ca]

yes, u need to heat the tubing up sometimes to get it on

Great as I have just ordered some. I will look a lot neater without clips.

 

[mrapoc]

but bigger tubes allow higher flow at less pressure so better temps right?

I'd rather get it all from one place...and a oc3d partner...ST...wcuk etc.

I need everything apart from the cpu block if all goes according to plan

 

[Mr. Smith]

I use 7/16" tubing over 1/2" barbs... No need for clips.

As for tubing diameter, there was an extensive test on XS on all tubing diameters which concluded there was next to no benefit for any size... It's all down to aesthetics and personal preference. I'd link you but there are too many threads over there to go through.

 

[mrapoc]

Both specialtech and watercoolinguk dont have 7/16" tubing in

 

[RaiderX303]

here, sold per foot http://www.chilledpc.co.uk/shop/product_info.php?cPath=34_44&products_id=161

 

[cuprasport]

chilled pc is a good shop, iirc watercoolinguk are closed till monday now anyway m8