Warlord Shigs
New member
right im at work atm and the only chip i ave here is a 3.0c sl6wu but its retail boxed. so b4 i open it i wanna kno wat can i expect from this chip? isit a good steppin?
3.0c P4 sl6wu
- Thread starter Warlord Shigs
- Start date
Warlord Shigs
New member
name='Bryan' said:
assystems mate. its my uncles business. where jus sortin out the website atm so prices aint fully up 2 date. but so u ave a rough idea its www.assystems.co.uk based in north london
Brwmogazos
New member
name='Warlord Shigs' said:
pack date?
FPO batch?
those chips are great mate...
i got one too...havent see what it can do on phase change though...
Warlord Shigs
New member
Brwmogazos said:
im hookin it up 2 my mach atm, fpo/batch: 3352a325
mm~: 852639
pack date is 01/19/04
Warlord Shigs
New member
ok atm its benchin the 3.0c @ 4.15. my last 3dmark01 socre at 4gig was 21964. aim aimin 4 22.500k hope i can get there. the chip is @4.15 with 1.7volts my corsair 3700pt v1.1 is runnin a 5:4 divider @ 3-4-3-7
Warlord Shigs
New member
name='aXeR' said:
ye i kno thats y i need new ram. i cnt run @ cas 2 i dnt think ive tried 2.5 yet tho. and no i aint v dimm mod my p4c800 deluxe is jus as it was out the box. aint 2 confudent in my soldrin skill atm. ill research into moddin my board tho. cos if all goes wrong i can jus change it as i run a computer shop wid my uncle
. but ye i jus got 22.5k in 3dmark 01 with my 3gig @4.2 with 1.75vcore. i need 2 get sum fast timin ram which can do 300fsb at a 5:4 divider. any suggestions, that dnt involve impossible 2 find bh-5 
Shigs with my sl6 I get to around 280 and that’s where is started needing my mobo mods. @ around 275 I start turning up the juice. Atm im hitting my geils (sames sticks as axer's) with 3.2 with slightly slacker timings than b4, im a bit scared of throwing < 3.3V's @ mem other than 4 benching 
. With 3.3 @ 292 fsb I can get 2-3-2-6. 3.2 gives me 2-3-3-6. I’m finding that the droop mod is really helping with stability @ the high fsb's. Ive stuck with 1.75 but the fluctuation is now so much better. Without the mods id see prime reduce the vcore in windows to around 1.58 which would always result in reboot. After a little tuning, idling I get 1.77 (1.73 on multimeter 1.75 in bios) and with 2X prime small fft's i get around 1.69.
ps I knackered my rubbish psu trying to do the 3V line mod in it so i haven’t touched my antec
. With 3.3 @ 292 fsb I can get 2-3-2-6. 3.2 gives me 2-3-3-6. I’m finding that the droop mod is really helping with stability @ the high fsb's. Ive stuck with 1.75 but the fluctuation is now so much better. Without the mods id see prime reduce the vcore in windows to around 1.58 which would always result in reboot. After a little tuning, idling I get 1.77 (1.73 on multimeter 1.75 in bios) and with 2X prime small fft's i get around 1.69.ps I knackered my rubbish psu trying to do the 3V line mod in it so i haven’t touched my antec
Thanks very much gorby, your info has proved what i thought was wrong with my PC, as soon as something demanding hit my CPU at 3.6ghz id reboot automaitcally due to lack of voltage. The only thing that needs fixing now is winamp, wen running with prime 95 on (at 3.45v) instead of rebooting it crashes winamp, but seems to only be wen once again something demanding hits the CPU< but its not quite bad enuff to cause a reboot.
Also its good to see I wont need to change my ram to run at those kind of speeds
@gorby, is 4.2ghz the max u can run stable? or is that what your limited too? if so wots limiting you, CPU, ram?
also whats temps you on at idle + load, u using a Mach2, right?
Also its good to see I wont need to change my ram to run at those kind of speeds
@gorby, is 4.2ghz the max u can run stable? or is that what your limited too? if so wots limiting you, CPU, ram?
also whats temps you on at idle + load, u using a Mach2, right?
Warlord Shigs
New member
gorby said:Shigs with my sl6 I get to around 280 and that’s where is started needing my mobo mods. @ around 275 I start turning up the juice. Atm im hitting my geils (sames sticks as axer's) with 3.2 with slightly slacker timings than b4, im a bit scared of throwing < 3.3V's @ mem other than 4 benching
ps I knackered my rubbish psu trying to do the 3V line mod in it so i haven’t touched my antec
mate have u got a link, with a guide how 2 mod the p4c800-deluxe vdimm and droop mod?
http://www.malvescorner.com/p4c800.htm
I recommend you have a very tiny bit for your iron and you will need a multimeter. I did mine in the week was fairly easy.
I recommend you have a very tiny bit for your iron and you will need a multimeter. I did mine in the week was fairly easy.
Warlord Shigs
New member
Ferret said:
thanks 4 teh link mate, was there a site u ordered all ur bits from?
Brwmogazos
New member
you will need a low wattage soldering iron...some suitable solder...steady hands and luck in order to do the mods properly and nice and neat....
just give it a go if youre confident...if not then...just leave it...you can mess up your board easily with the droop mod.
i did my board already and phils....i got 4 P4C waiting and a shuttle board as well..
just give it a go if youre confident...if not then...just leave it...you can mess up your board easily with the droop mod.i did my board already and phils....i got 4 P4C waiting and a shuttle board as well..
Maplins have variable resistors just like the ones shown, also used them for the multimeter, soldering iron and solder. You might want a magnifying glass too.name='Warlord Shigs' said:
Used an Antex 18W Miniature Soldering Iron Type CS, I would imagine 18W is around the max you would want to use, although I am no expert.
