OC3D Review: MSI P7N Platinum Nvidia 750i based motherboard

[mehdi19]

Thank you for the response Kempez and nice review seems like a great board I

might get one with two 8800gt the second slot not being 16x wont hamper performance too much right? and was the oce you achieved stable for gaming?

 

[FarFarAway]

I'm not too sure about the second x16 slot as the 8 series have got to the point where I think they saturate 8x bandwidth

The OC was stable for 1 hour Prime95 on all four cores

 

[Nebulous]

Anyone tried to OC this with a 1333MHz FSB CPU yet? I'll be trying it with an E8400 next week.

 

[Darksector88]

Just ordered the board and a q6600 and will receive today. BUT there is a problem of which many have encountered. One is the fact that many people with q6600 can only see two cores with this board, will a bio's update fix that? Also I have read that this board has a mean "FSB HOLE" anything around 1333Mhz to 1400Mhz from what I know of, which will keep me from getting my overclock I want to achieve (3.6Ghz maybe a little higher if doable) :nono:. If anyone has encountered this hole or have had any q6600 problem's with this board please inform me because right now I am thinking of an RMA and I haven't even recieved it yet. After I get it and test it anything I learn I will try to inform any who are wandering.

By the way nice review, did each core check out at 3.8Ghz in CPU-z, because many ppl haven't been able to pass 1333MHz FSB. If so, how did you get it to work?

Thank You

 

[FarFarAway]

Yep I got all Core's there in CPU-Z Didn't find an FSB hole either.

I did tend to use the VTT voltage a fair bit as Quad's thrive on those volts

 

[Darksector88]

thank you, got my board it was DOA I believe, no post, checked all hardware and it all checks out (played with the q6600 for a while on a MSI P35 board 3.6ghz overclock was nice 5310 on 3dmark06 cpu score).

All I could go by was that the board would display a red led on the bottom and blue led right above it. Don't know what that means but no video display on the screen, video card checked out though. Any ideas

 

[Luigi]

Sorry, cant help you there

 

[Icerider]

Hi guys a have a few question about the board where you able to achieve that oce with 4gb of ram? does the thermalright ultra extreme fit on the board?

and does it support tri sli?

Just got the board in from the egg. You will have to VERY carefully bend that curving top heatpipe about 1 or 2 cm toward the first pci slot to fit, it's not even enough that you notice but it does work with my TRUE with about 1 cm clearance after the bend. I do advise you pull the heatsink/heatpipe array off and replace the dope with some AC Ceramic. My southbridge wasn't making ANY contact (seems to be a very common problem on every manufacturers boards now days, not exactly a tough QC problem so go figure). On that note the heatsink seems pretty cheap so I may look at replacing the array with some other sinks. Couple of the Thermalright HR-05 SLI's on the north and south bridges, they're HR-09 type 3 on the mosfets, and a Thermaltake Extreme Spirit II on the 200 chip between the PCI-E's for some color But only if I can get it to clock better than my xfx 680i LT (I sure hope it does because right now the best I can get is 3.3g stable with a G0 stepped chip 1.25vid).

will let everyone know my results in a few days when I have time to play with it.

 

[Rezzie]

How

How did you manage to get the FSB to 470?

I have tried OCing my E8400, but the best I've managed is 3.6GHz stable using:

400MHz FSB (1600MHz in BIOS)

9x Multiplier

CPU @ 1.24V (+0.0350V in BIOS)

NB @ 1.32V (+ 2 steps in BIOS)

I'm getting CPU temp of 23-25 idle, 33 under load. Cores are between 33-39 under load.

I managed to raise FSB to 1667, giving 3.75GHz, which booted into Windows, but kept locking up fairly regularly. Temps were one degree higher.

Any advice? I have almost no experience overclocking, sorry - but I've heard the processor is capable of 4.4GHz+

 

[FarFarAway]

Try using the VTT voltage, upping that a bit helps

Can't remember the whole BIOS

 

[Rezzie]

Yeah, I wondered about that. It's default at the minute (1.2 I think?). What do you recommend I up it by, one or two steps in the BIOS? Or to a specific amount, say +0.1V etc?

Thanks for the quick reply (and fantastic review, big factor in me choosing the board)!

 

[FarFarAway]

Keep it on topic guys, those posts have been moved to a new thread in the overclocking section

 

[mbinzu]

Kempez could u tell me ur bios settings to get past 1333fsb, because my windows wont boot over that number, so i think maybe something needs being disabled or enabled in bios (p7n platinum q6600)

 

[alexbebe]

hi guys i have a question for u....

i bought this mobo and i wanted to buy an Cooler Master Sphere cooler ...but i do not know if will fit beacause of the zalman cooler onto the chipset ....

should i'll try another cooler like Cooler Master GeminII s?or the Sphere

i like a lot the Sphere but i do not know if will fit...thx

ps:sorry for my bad english

-------------------------------------------------------------

config:

case:antec nine hundred

power_s:780w sli ready

mobo:msi P7N SLI Platinum

cpu:intel q9450

mem:Mushkin quad pack 4x 2GB

gpu:leadtek 9800gtx+

hdd:2x500 seagate sata2