re mach 2 temps

[Dazboots]

re mach 2 GT temps

thanks every1 for the great info on my low bad temps.

sorted it now was bad contacts.

this ((mach 2 GT)) is the mutts nutts.

far better than my mach 2

GETTING TEMPS OF -69

and thats overclocking my 3.2 extreme edition at 4.288 mhz 1.85 volts stable.

going to try and get over 4.3ghz by pushing more volts in.

will keep u posted.

thanks again phill u was right after all. nice 1 .

and my motherboard monitor shows -24

 

[Brwmogazos]

i never got temps of -69C with my mach 2 GT

wtf?

is that with fans on full?

i get like -49C idle and -44C load....

cpu temps of -39C to -40C idle and -22 load @ 1.75V

 

[Dazboots]

sorry to give out the bad news but i get while overclocked

extreme edition 4.1 ghz 1.82 volts idle -69

when doing the beat the office benches it goes down to -54

put double washers on each of the springs that goes into the cooling head.

my temps r unbelievable. holds temps very good. hope this helps.

and my fans r on manuel turned up full both.

 

[aXeR]

Nice temps on your evap, wot u get on ure CPU tho?

on my straight mach 2 with fans on full i get about -50-55 (room temp permiting) on idle and about -45-40 on load (that was at 3.9Ghz, 1.8V) but i dont like it on max fan speed its noisy, i settle for just less than half speed which is still -45-48 idle on evap and -35 on load

 

[Dazboots]

Nice temps on your evap, wot u get on ure CPU tho?

on mother board monitor it shows -24 while overclocking to 4.2 ghz 1.82 volts

idle. extreme edition 3.2 ghz

 

[Warlord Shigs]

Nice temps on your evap, wot u get on ure CPU tho?

on mother board monitor it shows -24 while overclocking to 4.2 ghz 1.82 volts

idle. extreme edition 3.2 ghz

wats the highest safe volts u can run on a p4 24/7? 1.75 volts or 1.85??

 

[Dazboots]

wats the highest safe volts u can run on a p4 24/7? 1.75 volts or 1.85

i run mine 24/7 1.825 volts

 

[Brwmogazos]

For non 30cappers 1.75V is supposed to be safe..never had probs with mine

for 30 cap cpus 1.85V is supposed to be ok...they love voltage

 

[Phil Stanbridge]

My evap temps are around -75 idle how this relates to the real world is anyones guess. Tongue = evap head = stuck.

My load temp on the Fx was around -10! These chips are toasty!

 

[Dazboots]

My evap temps are around -75 idle how this relates

i have a abi-ic7max 3 moherboard

overclocked this shows in bios -10

3.2 overclocked o 4.2 1.825 volts is his right.

 

[Brwmogazos]

phil u wanna swap your gt with mine?

i never got that low evap temps...in fact i get like -50C to -51C @ 1.75V idle

 

[Dazboots]

phil u wanna swap your gt with mine?

here is some good advice on good temps.

only use small amouns of seal string.

go to he edges and use only 1 piece of string.

on the head put extra washers on each thread, i put 2 on each.

tighten as much as u can.

here u go all the best.

 

[Brwmogazos]

i dunno why i always had worse evap temps than many mach 2s....

my cpu tempswere fine though

i am already using one washer extra...one layer of seal string etc

my cpu temps seem fine so it seems my sensors are more accurate or i get better contact thats why my evap temps are lower and my cpu temps are great

dunno just a thought...

for now on air till i get my rig sorted

 

[[O-CuK]Marci]

My evap temps are around -75 idle how this relates to the real world is anyones guess.

About -46 deg C in real-world temps. The unit can never be colder than the refrigerants actual evaporating temperature.

 

[standin wave]

Evap temps

According to nother post in excel, evap temps were

Heat load

0W 100W 180W

Vapochill LS -45.3°C -28°C -26°C

Mach II ST -51.0°C -35°C -26°C

Mach II GT -65°C -48°C -38°C

So the reported temps are inaccurate!

sw

 

[standin wave]

sorry about crappy formatting

sw