mach ll and asus a8n sli deluxe

[Dima]

Can anyone help me. At this moment i have the following configuration:

asus a8n sli deluxe

amd 64 3500 processor

2x 512 a-data 3200 memory

3 maxtor hard disk 80 gb

2 club 3d geforce 6600gt video

mach ll

the problem is that the computer doesn't startup automaticly. after the mach ll reahces boot temp the computer has to be start up by hand?

I did an firmaware update makes no diffrent. Can somebody give me some usefull information

 

[Phil Stanbridge]

Hi there mate,

Ok what Mach II are you running and what firmware and software are you running?

 

[Dima]

I have an mach ll (not gt, not st), the firmware is version 821. using windows xp prof sp2.

Hi there mate,

Ok what Mach II are you running and what firmware and software are you running?

 

[smokie]

Sounds silly but have you checked that you have the wires the right way round??

I.E The mach going into the mobo and the power wire from the pc going to the mach!! If they aren't connnected right then that will stop your pc from booting. Also check the molex connector which attaches the mach to the pc too.

Although if this isn't right the mach would turn off straight away after reaching boot temp so i think that one is ok!!

Hope that helps

Greg

 

[Dima]

No not a silly question, but the cables are connected right.

Sounds silly but have you checked that you have the wires the right way round??

I.E The mach going into the mobo and the power wire from the pc going to the mach!! If they aren't connnected right then that will stop your pc from booting. Also check the molex connector which attaches the mach to the pc too.

Although if this isn't right the mach would turn off straight away after reaching boot temp so i think that one is ok!!

Hope that helps

Greg

 

[Dima]

Hello, help needed??

Hello, please can anyone help me with mine problem, see belowe for the problem. I have tried several possible solutions all with the same result (negative)

Can anyone help me. At this moment i have the following configuration:

asus a8n sli deluxe

amd 64 3500 processor

2x 512 a-data 3200 memory

3 maxtor hard disk 80 gb

2 club 3d geforce 6600gt video

mach ll

the problem is that the computer doesn't startup automaticly. after the mach ll reahces boot temp the computer has to be start up by hand?

I did an firmaware update makes no diffrent. Can somebody give me some usefull information

 

[Firelord]

Is it a newcastle or a winnie core'd 3500+?

 

[Dima]

It is a newcastle

Is it a newcastle or a winnie core'd 3500+?

 

[Firelord]

Does the system boot on air?

 

[Dima]

Yes

Does the system boot on air?

 

[Firelord]

Hmmmm

Right boot the prommi up with a seperate PSU and when it reaches the boot temp check that you get a volt meter and check that you get some voltage through the power on switch cable

(I think that makes sense

 

[maverik-sg1]

This is an easy one for me having set-up two systems with this set-up alebiut with winchesters.

The problem I have seen is one where every time you boot up you have to go into the BIOS, save and exit then restart, if this is your issue the solution is simple:

Update the BIOS to the latest version from Asus, all will be resolved and you can move forward with confidence. At least thats what I had to do, hopefully it will be the same for you.

Cheers

Mav

 

[Dima]

I have done what you told me and the result is that there is no voltage through the power on switch cable!!

Hmmmm

Right boot the prommi up with a seperate PSU and when it reaches the boot temp check that you get a volt meter and check that you get some voltage through the power on switch cable

(I think that makes sense