Go Back   OC3D Forums > [OC3D] Project Logs & Gallery > Rig Gallery
Thread Tools Search this Thread Display Modes
Prev Previous Post   Next Post Next
Old 09-07-21, 01:16 AM
Bartacus Bartacus is offline
OC3D Elite
Join Date: Apr 2013
Location: Ottawa, ON, Canada
Posts: 2,743
Case Labs, the case I cannot escape from.

Intro: every since I was fortunate enough to lay my grubby old hands on a 6900XT (Asus TUF Gaming OC), I noticed something: it was unhappy. At first it was unhappy for obvious reasons: the included factory air cooler sucked copious amounts of bum. This was rectified eventually, by an Alphacool water block. But still, it was unhappy. Eventually I had to face a harsh fact: the Lian-Li Dynamic O11 XL, a case I liked so much I bought TWO of them, is in fact a hot box, especially when using triple radiators. There is no getting around this fact. Unless your fans are running constantly, it's an oven. A very pretty oven. Now as someone who likes to run his GPUs OCed (because this is OC3D after all), this had to change. Therefore the decision was made to move my gaming rig back into a Case Labs Magnum M8, with pedestal. For more breathing space. And more rad space never hurt either.


Ryzen 5950X CPU on Gigabyte Aorus Master mobo / TechN CPU block
64GB RAM (4x16GB G.Skill Crystal Pimp Silliness 3600mhz CL16)
Asus TUF Gaming OC 6900XT / Alphacool GPU block
1TB Corsair MP600 NVME / 2TB Corsair MP600 NVME PCIE4 SSDs / 1TB Intel 600p PCIE3 SSD
EVGA 1000W Gold PSU
Dual D5 pumps on a Singularity Computers Resonance dual D5 distro plate
2 x Alphacool Monsta 88mm radiators / Darkside Gentle Typhoon 1850RPM PWM fans
2 x Darkside LP360 radiators (Mix of Fractal Design Prisma AL-120s / OG Nidec Gentle Typhoons)
1 x Darkside LP240 radiator (Darkside Gentle Typhoons)


Tearing down my Threadripper rig to displace it:

Worlds worst drain, installed backwards for reasons I cannot explain, other than I'm an idiot with a capital AYE!

Several hours of swearing later:

Three simple 90 degree bends was all I needed this time:

My new favorite AM4 block from TechN:

Rigged up a snorkel for filling / bleeding the loop, since distro plates are a bit trickier than tube reservoirs:

In spite of how bad this looks, there was some cable management done, really:

Flow meter / temp sensor / coolant critic installed, below a GPU block with a dead light strip that worked for a grand total of one day:

Resonance Dual D5 plate from Singularity Computers, not lit up because I broke the LED strip, twice.

Let there be purple. Well, in cases where the lights actually *work*:

No, it is not exactly the world's smallest case:

But so worth it. Now my GPU can breathe properly:

As for temps now, after 3+ hours of endlessly looping every stress test in the 3dmark suite, the top GPU core temp I saw was 41C / hottest junction temp was 64C. That's on a GPU with the power limit upped from 272W to 375W, and still retaining the 15% power slider, while running a max core of 2750mhz, max memory speed of 2150mhz, fast timings / resize-able BAR enabled. It floats between 2650 - 2700mhz+ in game, at much cooler temps. Mission accomplished!
Games: Ryzen 5950X on GB Aorus Master X570 / Asus TUF 6900XT / 32GB TridentZ Neo 3600CL16 (16GB x 2) / custom loop
Workstation: Threadripper 2950x on GB Aorus Xtreme X399 / Zotac 2080ti / 32GB TridentZ 3200CL14 (8GB x 4) / custom loop
Home Theatre: Ryzen 3900X on Asus C7H X470 / Radeon VII / 16GB G.Skill 3600CL15 (8GB x 2)
/ custom loop
Reply With Quote

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT. The time now is 11:21 PM.
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2021, vBulletin Solutions, Inc.