Go Back   OC3D Forums > [OC3D] Processors & Platforms > Mainboard & CPU
Reply
 
Thread Tools Search this Thread Display Modes
 
  #1  
Old 16-06-21, 04:59 PM
Sythen's Avatar
Sythen Sythen is offline
Newbie
 
Join Date: Feb 2015
Location: burrmingum
Posts: 48
Send a message via Skype™ to Sythen
Asus Maximus VII impact repair help

Evening all!

So a friend gave me a load of bits from her old rig, as I just built her a new one.

After inspecting the motherboard (name in title) I noticed that a wire wound inductor on the rear of the board has had its head knocked off.

This in itself isn't an issue for me, but id appreciate it greatly if someone could confirm the value marking on this component.

After snooping around the net, I found an image that I *think* it says 4R7.

If anyone has one of these boards kicking about, and you could snag a picture or just confirm if I'm right or wrong. I'd greatly appreciate it!

Reply With Quote
  #2  
Old 16-06-21, 05:40 PM
Sythen's Avatar
Sythen Sythen is offline
Newbie
 
Join Date: Feb 2015
Location: burrmingum
Posts: 48
Send a message via Skype™ to Sythen
Just as a follow-up, I was able to find a boardview of this motherboard, and was able to confirm the value and spec of the inductor.

Reply With Quote
  #3  
Old 16-06-21, 06:19 PM
hmmblah's Avatar
hmmblah hmmblah is offline
Moderator
 
Join Date: Jul 2010
Posts: 4,730
I used to have this board, but sold it awhile back. Scoured the internet for you for close up images of the back, but so many were too low resolution to read. Finally found one though, but it looks like you found your answer lol. Can you link where you found the boardview?

A little late, but here's the picture anyway

__________________
CaseLabs Mercury S3 | AMD 3900X | ROG CH8 Impact | RTX 2080 Super | 32GB DDR4 | 1TB NVMe
Acer Predator Z35P


Reply With Quote
  #4  
Old 16-06-21, 07:37 PM
Sythen's Avatar
Sythen Sythen is offline
Newbie
 
Join Date: Feb 2015
Location: burrmingum
Posts: 48
Send a message via Skype™ to Sythen
Thanks for ya input! yeah, looks like it was 4R7, i ordered some replacements from RS Components.

The site was sketch AF. but here is a google drive link to the .fz file. you will need some boardview software to display it. https://drive.google.com/file/d/1Lme...ew?usp=sharing
Reply With Quote
  #5  
Old 19-06-21, 07:05 AM
Sythen's Avatar
Sythen Sythen is offline
Newbie
 
Join Date: Feb 2015
Location: burrmingum
Posts: 48
Send a message via Skype™ to Sythen
Not completely flat (hot-air station is fubar right now)

But not too bad!

Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump










All times are GMT. The time now is 07:46 PM.
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2021, vBulletin Solutions, Inc.