Go Back   OC3D Forums > [OC3D] Project Logs & Gallery > Project Logs
Reload this Page BackDraft Evo (a Nanoxia DS1 Build)
Reply
Page 4 of 25 « First 23 4 5614 Last »
 
Thread Tools Display Modes
 
  #31  
Old 25-05-13, 09:21 AM
23RO_UK's Avatar
23RO_UK 23RO_UK is offline
Member
  
Join Date: May 2013
Location: Kent, UK
Posts: 212
The Postie delivered some more goodies this morning...


2 of E22's finest 120mm FG01 Fan Grills








Made from brushed stainless steel they are absolutely mint quality!!!


Thanks again Nate you're an absolute star mate!!!

Reply With Quote
  #32  
Old 25-05-13, 09:21 AM
23RO_UK's Avatar
23RO_UK 23RO_UK is offline
Member
  
Join Date: May 2013
Location: Kent, UK
Posts: 212
And here are a couple of teaser pics...





Reply With Quote
  #33  
Old 25-05-13, 09:28 AM
AverageNinja's Avatar
AverageNinja AverageNinja is offline
Average Penis Too
  
Join Date: Apr 2012
Location: The Netherlands
Posts: 3,251
Very, very nice! I like the nanoxia!
Good luck with your loop mate
__________________
JavaBean: Ryzen 5 1600 / Corsair ML240L RGB / ASUS Crosshair 6 Hero / 16GB Corsair LPX / ASUS RX 580 Strix / Corsair RM750X / Fractal Design Meshify C

OC3D Overclockers Club Member:
Nr. #00 (Club Owner)

Reply With Quote
  #34  
Old 26-05-13, 11:56 AM
23RO_UK's Avatar
23RO_UK 23RO_UK is offline
Member
  
Join Date: May 2013
Location: Kent, UK
Posts: 212
Quote:
Originally Posted by AverageNinja View Post
Very, very nice! I like the nanoxia!
Good luck with your loop mate
Thank you
Reply With Quote
  #35  
Old 26-05-13, 11:57 AM
23RO_UK's Avatar
23RO_UK 23RO_UK is offline
Member
  
Join Date: May 2013
Location: Kent, UK
Posts: 212
Right this morning saw me remove the motherboard to install the CPU water block.

Presenting one installed EK Supreme LTX CSQ CPU Copper Acetal Waterblock...








I've used black M4 nylon dome nuts to allow me to visually gauge how much spring tension I've applied at each thread and to stop anything snagging on them as the build progresses.

I might actually leave them there as I think they look aesthetically pleasing
Reply With Quote
  #36  
Old 26-05-13, 11:58 AM
23RO_UK's Avatar
23RO_UK 23RO_UK is offline
Member
  
Join Date: May 2013
Location: Kent, UK
Posts: 212
More of this mornings progress...


That's the rear extract 140mm Xilence CF2 mounted








I've used anti vibration mounts to eliminate noise as much as possible





Installed the Power Supply Unit





I'm using a Seasonic X-Series 650W Full Modular Power Supply





And pre installed the dual 8-Pin EPS12V Extensions





Plus the 24-Pin ATX Extension





These are just some eye candy shots





Reply With Quote
  #37  
Old 27-05-13, 10:36 AM
23RO_UK's Avatar
23RO_UK 23RO_UK is offline
Member
  
Join Date: May 2013
Location: Kent, UK
Posts: 212
Ok that fateful day has arrived...


Has all my measuring up and research paid off???


A busy morning so without further adieu


One prepped Alphacool NexXxoS ST30 240mm Full Copper with mounted twin 120mm Xilence CF2's and EK EN PSC 14 Compression Fittings.








And here's my baby all prepped again with twin 120mm Xilence CF2's, E22 120mm FG1 Fan Grills and EK EN PSC 14 Compression Fittings.





Reply With Quote
  #38  
Old 27-05-13, 10:37 AM
23RO_UK's Avatar
23RO_UK 23RO_UK is offline
Member
  
Join Date: May 2013
Location: Kent, UK
Posts: 212
And now the installation...


First up the Monsta








Millimetre perfect








Next up the ST30








And here we have the end result


(HUGE sigh of relief)


Success


Reply With Quote
  #39  
Old 27-05-13, 10:52 AM
sheroo's Avatar
sheroo sheroo is offline
OC3D Elite
  
Join Date: Jan 2011
Location: U.K.
Posts: 3,232
Perfect fit - that's what she said...
__________________
"All his life has he looked away... to the future, to the horizon. Never his mind on where he was."

Reply With Quote
  #40  
Old 27-05-13, 11:20 AM
Feronix's Avatar
Feronix Feronix is offline
OC3D Elite
  
Join Date: Aug 2012
Location: The Dungeon
Posts: 7,683
Looking good, mate!
__________________
~Rick

"If a bear looks good in the woods when nobody is there, is he still a cool ass motherf***ing bear?" - JR23
Reply With Quote
Reply
Page 4 of 25 « First 23 4 5614 Last »

Tags
e22, evga, mnpctech, nanoxia deep silence 1, z68 ftw

« Previous Thread | Next Thread »
Thread Tools
Display Modes
Linear Mode Linear Mode

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump










All times are GMT. The time now is 06:40 PM.
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2021, vBulletin Solutions, Inc.

Contact Us - OC3D Forums - Archive - Top