Recent content by Geomon

Can any users of the Dfi sli-dr expert boars tell me if they are experiencing cold boot issues. I have been using this board for a while now with a new set of mushkin redlines and for the first few weeks the board and ram has been great. Over the last week I tried 260ht at lower timming than...

I am toying with the idea of removing the heatspreader from my 57FX but have heard some horror stories about resistors also being removed too. Does anyone know a good method of how to remove the ihs or have any tips to help me. I have a busted 3500+ that I will practice on first.

Ok I am using these settings on my dfi expert with a 57fx and a set of redlines. They are parameters the Mushkin say are to most stable for there ram(except for the ht/fsb, multi, and vcore). What I want to know is that altough stable is there any settings that would have a bad effect on the...

Just wondering if anyone had used the ntune memory benchmark. Its a very simple and quick test that is hardly reliable but I was wondering what scores peple are getting on it. Its best to run it just after booting into windows and the first 3 runs are the best. It scores your ram on read...

I got a tough choice to make about which ram to keep. Its between Mushkin Redline xp4000 UT or Ocz VX4000. The Redline are the better overclockers doing 265ht at 2-2-2-6 before burn in, the Vx do 255ht also at 2-2-2-6. I have benched them with a few very basic benchmarks at the exact same...

Just though I would share some recent good news about an RMA. I just got back my RMA from Mushkin for a set of Redline XP4000 UT modules that died on me a while back, the old ones done 255HT at 2-2-2-6 before burning in. The RMA replacment modules that arrive are the new type with the fancy...

Had anyone had any experiences with the new Geil One Bh5 ram modules? These ram sound great and are also priced very well. I want to know how they compare against either the Mushlin Redline XP4000 ut modules and the Ocz pc4000 VX range. The main thing I would like to know is how they compare...

Finlly the verdict on the board we have all been waiting for. And it looks to be a good'n:D http://anandtech.com/mb/showdoc.aspx?i=2620 Also have a look at this: http://cgi.ebay.co.uk/DFI-LANPARTY-UT-NF4-SLI-DR-EXPERT-NEW_W0QQitemZ6823959500QQcategoryZ31496QQssPageNameZWD2VQQrdZ1QQcmdZViewItem

On reading up on a few reviews of the Mach 2 GT's I have found that the lables on the compressors differ from one unit to another. Some of the lables are green and state the numbers nf9fx "5933" and NF9FX in the top left hand corner, the others are yellow and state "6900" and NL11F on the left...

My mach 2 gt is due to be delivered today via citylink between 9-530pm. I have been told that I need to let it stand for 12hours before I use it:( . I will use this thread for the many problems I am sure to encounter with the install and overclocking with it, any tips, advice that you guys...

Just to confirm beforw I buy. I need a 114mm hole cutting saw for a thermochill HE120mm rad yes? Gonna be cutting a Lian Li pc65. Reason I ask is that I see some shops selling 122mm saws but the blowhole cutting guide in the section states that a 114mm saw is needed. Thx:)

Has anyone run a Mach 2 GT with a Lian li pc75? The reason I ask is that I just got a pc65 to replace my old pc75 so I can easyilly fit the GT when it arrive but had no idea it was soo small compared to the pc75. I think the pc75 is a far better case and it would be such a shame to lose it...

If you have a Dfi nf4 motherboard running some BH5 ram this may be of interest to you. I recently purchased 2x512mb of Mushkin Redline XP4000, these modules are based on the Winbond BH5 UT memory chips and can out perform pretty much anything available providing they have access to voltage of...

I have purchased a new 57-FX and have started to overclock it on water. At present I am a little dissapointed with its abillities in its o'clocking. I have been running it at 2.972 100% prime stable but needed a whole 1.530vcore to do so. I think I could get a 3ghz stable clock with some more...

I am abouts to upgrade my 68gt to one/two of the latest top spec cards. This upgrade will be at the start of December(payday). I did have my sights set on the ATI 1800xt but am now thinking to go 512gtx. Who is the daddy out of these two? I wont the best performance after both have been...