Recent content by Blyths

Hi all, I was browsing the internet & I saw that a guy is doing upgrades on mach units. The upgrade includes 1. Chilly 1 head & captube 2. Desuperheater coil 3. Regas to R402a This costs about £200. Is it worth it? I would like to hear your guys opinions. Thanks

Hi Guys, I know there are some old guides out on the web regarding installing the Mach 11, but would it be possible for one or a few of you to produce a Pic by Pic guide? The Cpu sets are now in metal which will scare most people, and I believe with most guys now moving to Skt 775, it can be a...

Hi guys, I have been having a lot of trouble with my computer just restarting for no reason, and then recently the Mach11 cools to -33 and nothing happens? like no power getting to the motherboard! It just goes to about -45, and shuts down. I removed the motherboard, and when I took off the...

Sorry if am in the wrong bit, but my problem is that my computer started restarting itself randomly? I would be in the middle of something then Off goes the screen and it restarts with the mircosoft "you have just recovered from a serious error" message. Then the other day it got stuck in an...

Hi all, I bought a DFI SLI-DR board, but am stuck with the 4 LED bug. I have read all the forums and there seems to be no answer to it. Even when boards are RMA ed they often get returned back because they work fine when tested. My board will boot fine, but if I have to do a power off it...

Hi all, I deceided to use my spare parts to build a comp for my daughter, I had it all rigged up and nothing happened.No signal sent to the monitor which I have checked. I checked the power supply and that was getting power to the motherboard as the green power lights were on. So i have just...

Hi All I seem to have a prob with this motherboard! Every time I have a software prob and I need to re-boot, I cannot boot back into windows or even the bios! I get 4 red LEDs and nothing. I have to jumper the bios to clear it, then hopefully it will eventually boot into the bios. Then I re...

Hi All This is likely a stupid question, but are you meant to have all 4 power connections on the DFI SLI-DR motherboard connected? (5/12v) At the moment I have connected the main ones ie ATX 24 pin and 4 Pin and it seems to work fine. Thanks

Hi All Just Began Overclocking ( my Spec just be below ) I have manged to get to 240 X 11 = 2640 Cpu 240 X 4 = 960 HT At Stock Voltages. If I try to increase RAM voltage the system wont boot to windows. Is this a fault with my Memory and this board do you think? So it looks like I will...

Hi All I know that the temp reading on the Mach II isnt spot on but as a guide line are these temps OK AMD64 X2 4200 @ stock Go,s down to -52 then to -42 in windows. Just so i know i have a good contact before I start Over Clocking. Many Thanks

Hi All Sorry to ask this question but on the DFI SLI-DR I have the USB from my MACH II connected like this 1 2 3 4 5 1 2 3 4 X ( My motherboard is upside down ) R W G B I believe this is right but I get USB connection Failed. Do I Just need to unplug it, boot the computer, then...

Hi All Just a check am getting the right sort of stock scores on my system before I Commence Over-Clocking. AMD64 Athlon X2 4200 2 x 512 PC4400 (OCZ) 2 x 7800 GTX MACH 11 3DMark05 - 11,106 3DMark2001 - 25,729 3DMark03 - 28,447 Aquamark - 85,911 Thanks

Hi all, Is there a problem with OCZ PC4400 DDR EL Duel CH (Gold Ltd Edition) and the DFI N4 SLI-DR motherboard? I have 2 x 512 Its just that when the computer crashes/freezes, it wont re-boot at all. The monitor just stays on standby. I have to keep jumping the Clear Bios on the...

Hi When i try to run 3Dmark05 I get direct3dcreate9 - failed Anyone know why? I have a 7800GTX, AMD64 4200X2, latest drivers installed. Thanks

HI all, I have just Built a new system, and when I turn on the MACH II it cools to its correct Temp -33, then the motherboard fires up, but only for about 2 secs before shutting down! ( So i presume the MachII is fitted right and is working correctly ) The MB is a DFI NF4 SLI-DR, the 2...